Multi-line 2 BGC Application Software series 1.x.

1.10.3

15/05/2015

Changes:

• Update of self-check functionality

1.10.2

23/02/2007

Changes:

• Menu for Voltage Trip (Phase-Phase or Phase-Neutral) removed.

1.10.1

21/02/2005

Changes:

• Handling of MB in VDE0108 AUS mode updated.
• Rampdown updated.
• Returning from JUMP menu sets to main view.
• Mode "Load take over" updated.
• Digital input alarm handling updated.
• Emergency stop default set to OFF.

1.10.0

07/02/2005

Changes:

• Setting if WARNING fail class should autoreset or not added
• Analogue input readings optimised for better precision
• Alarm acknowledge updated for option VDE0108
• Factory settings of var export/import changed
• interface to USW regarding inputs optimised
• Analogue input board (option M15) reading optimised
• Test mode updated

1.05.0

05/01/2005

Changes:

• When breaker position is unknown, breaker LED will be flashing red.
• Now possible to open GB in Island SEMI when Loadshare not present and breaker alarms active.
• Ramp down added to TEST mode.
• GB opens immediately in MAN mode when activated.
• RPM max. settings changed from 2000 to 4000. Overspeed alarms corrected according to this. Improved handling when using external power setpoint.
• Password to changing password changed. Must use master password level to change master password. Must use OEM password level to change OEM password.
• In VDE0108 alarm horn is now set off when first alarm of multiple alarms is acknowledged.
• Display is updated when using binary input for alarm acknowledge

1.04.5

12/11/2004

Changes:

• Governor and AVR offset function modified

1.04.4

19/10/2004

Changes:

• Manual stop in AUTO mode is changed
• Test mode handling changed
• Handling of other languages than English is changed

1.04.2

01/09/2004

Changes:

• Handling of mains breaker supervision when using contactor setting changed to avoid alarm when combined with zero-voltage coil trip of mains.

1.04.1

02/08/2004

Changes:

• Gen-set will ramp up in TEST mode.
• Underlined characters of extended ASCII-table added.

1.04.0

28/06/2004

Changes:

• USW interface improved
• Reset regulation functionality adjusted
• Settings possibilities for Emergency stop-menu extended
• Handling of GB and MB modified

1.03.1

09/03/2004

Changes:

• Manufactor name for CAN-open option changed
• Option H4 - minor chnnges
• USW interface regarding GB and MB extended
• Alarm inhibit functionality changed during stop-sequence
• Short circuit protection functionality changed
• Failclass 'Warning' functionality improved
• Functionality of frequency and voltage acceptance detection changed
• Check of language added to USW control
• GSM option menu extended
• Service timers functionality added to USW
• Event log update functionality changed
• GB feedback handling changed
• Single running in Island-mode functionality changed
• Running hour calculation improved

1.03.0

11/02/2004

New features:

• Modeshift can now be controlled with digital input or menu 4440
• Stop mode in menu 4900 added
• Option for support of VDE0108 is added
• GB position error can be deactivated (digital configurable input set to 'not used')
• Kvarh (import / export) counter added
• Sprinkler-mode functionality changed to include Short circuit 1,2
• Start attempt counter added
• New menu for number of sprinkler start attempt is added
• 'Load take over'-mode added
• Emergency power relay output added
• Collective fault output added
• 'Ready for operation' functionality added
• Possibility for activation of Test mode with conf. digital input added
• Possibility for 2 X option M13 or M14 added
• SMS module updated with ID number in every message
• SMS module updated with alarmbuffer, all alarms will now be sent
• Modbus communication is optimised

Changes:

• SMS module is stopped if no phone-numbers are used
• CCM communication is optimised
• W_L menu and functionality removed
• Static charger menu and functionality removed
• Voltage level for running detection changed
• Timing changed, if modeshift is on and mains failure occur
• 'Peak current' renamed for 'Short circuit'
• H4 option shown in USW
• If a mains fail occurs during TEST mode the AMF sequence will start
• USW stop command optimised
• Static sync improved function
• Improved power factor calculation
• Password handling optimised
• Menu handling in regard to Option A1 A2 A3 optimised
• Default setting for secondary value for current trafo's for Generator and busbar changed
• Counter handling (hours, CB, MB operations) optimised
• Deload is interrupted if remote start/stop is changed from start -> stop -> start
• MB operations optimsed during change of configuration
• Function of Relay 13 optimised
• Menu handling in regard to loadshare PCB optimised
• Menu handling for Option M13 optimised
• Possibility for Test-mode in Island mode removed
• Mains-failure detection improved
• Start enables functionality improved
• Log-functionality improved
• Failclass handling in auto mode optimised

1.01.2

07/11/2003

Changes:

• Security regarding write/erase operation in boot-sector is improved.

1.01.1

10/10/2003

Changes:

• The 8 Start/stop menus are adjusted
• Menu 4250, 'ID BAUD' -> 'TYPE' corrected

1.01.0

03/10/2003

New features:

• Can-Open support enabled
• 'JDEC' engine communication added

Changes:

• Line 3 adjusted when 'mode button' is used
• Eventlog secured when power up less than 3sec
• Frequency measurement below 20Hz is disabled due to a problem under stopping the gen-set.  This could in rare cases generate a reset of the unit.
• Timing in case of 'MB trip externt' adjusted

1.00.4

29/08/2003

Changes:

• Changed max limit in menu 1290 1300 from 300% -> 350%
• Changed text string for 2180 + 2190 (Deadband - > limit)
• Removed PF control settings, not used

1.00.3

01/08/2003

New features:

• Option H4 CCM Caterpiller

Changes:

• SMS phonenumber-interface to USW adjusted
• Peak-current measurement improved
• dfdt and vector-jump function improved
• Stop of gen-set if mains-fail is added
• Energy counters added

1.00.2

01/07/2003

New features:

• Possibility to configure input for Alarm Acknowledge added
• Possibility to configure input for Alarm Inhibit added
• Possibiblity for activating fuel-logic

Changes:

• Close of MB in auto changed
• Text changed: 'Sprinker' -> 'Fire pump'
• Generator protection moved into Option C1
• Display update sequence optimized
• VDO-input for fuel-logic is optimized

1.00.0

30/06/2003