Multi-line 2 AGC Application Software series 4.x.
You’re about to download Multi-line 2 AGC Application Software series 4.x.
The software you are trying to download is obsolete. Please download the latest version from this page.
You have chosen to download our software.
Whitin a few seconds, you will receive an e-mail containing a download link.
Having trouble using the software? Please contact support@deif.com.
Best regards,
DEIF A/S
The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software
This software applies to the following DEIF products:
You’re about to download 4-80-0
The main changes implemented since the last version are as follows:
PM compatibility: 1.22.0.
Option N compatibility: Minimum SW version 2.00.3 is needed, because the limitation of 4000 text strings is exceeded.
New features:
- Configurable spinning reserve request using parameter 8930 (not supported in BTB applications).
- The remote maintenance box (RMB) is now supported in an island Power Management configuration up to 32 DGs (requires option T4).
- Blocking of nominal parameter set change when engine running is added. The new parameter 6016 in DG is only available from the USW.
Changes:
- Support of ASC-4 redundancy.
- Shows Racked out breaker On/off in the log.
- Shows Tier-4 symbol for Scania S8 inducement failures.
Corrections:
- Fuel optimization + running hours does not change at fixed load.
- Corrected: Configurable amount of Fatal CAN error alarms could change when multiple units were powering up.
- Corrected: Configuring a mains stand-alone application with the CAN bus set to OFF in the application configuration prevented the MB from closing.
- Corrected: If a DG was running with its GB open and ground relay closed, and a mains then connected to the busbar, the ground relay would open.
- Alarm texts from DVC550 are now shown correctly.
- Added an alternative engine speed control for Volvo protocols including counter and checksum. Can be enabled with the new parameter 15110.
- Added a Power derate calculation low limit for inverse proportional slope (only used for multi-inputs 102, 105 and 108 configured as mA measurement.
Ver. | Date | Description |
---|---|---|
4-80-0 |
26/11/2020 |
PM compatibility: 1.22.0. New features:
Changes:
Corrections:
|
4-79-3 |
17/09/2020 |
PM compatibility: 1.18.0. Corrections:
|
4.78.0 |
19/05/2020 |
PM compatibility: 1.17.2 New features:
|
4.77.1 |
31/03/2020 |
PM compatibility: 1.17.2. Corrections:
|
4.77.0 |
11/03/2020 |
PM compatibility: 1.17.2. New features:
Changes:
Corrections:
|
4.76.1 |
03/02/2020 |
PM compatibility: 1.17.1 Corrections:
|
4.76.0 |
23/01/2020 |
PM compatibility: 1.17.1 New features:
Changes:
Corrections:
|
4.75.0 |
12/12/2019 |
PM compatibility: 1.17.1. New features:
Changes:
Corrections:
|
4.74.4 |
01/10/2019 |
PM compatibility: 1.17.0. Corrections:
|
4.74.3 |
11/09/2019 |
PM compatibility: 1.17.0 Corrections:
|
4.74.2 |
07/08/2019 |
PM compatibility: 1.17.0 Corrections:
|
4.74.1 |
10/07/2019 |
PM compatibility: 1.17.0 Corrections:
|
4.74.0 |
07/06/2019 |
PM compatibility: 1.17.0 New features:
Changes:
Corrections:
|
4.73.1 |
02/05/2019 |
PM compatibility: 1.17.0 Corrections:
|
4.70.0 |
04/04/2019 |
PM compatibility: 1.17.0 New features:
Changes:
Corrections:
|
4.71.0 |
04/04/2019 |
PM compatibility: 1.17.0 New features:
Corrections:
|
4.71.1 |
04/04/2019 |
PM compatibility: 1.17.0 Corrections:
|
4.72.0 |
04/04/2019 |
PM compatibility: 1.17.0 New features:
Changes:
Corrections:
|
4.73.0 |
04/04/2019 |
PM compatibility: 1.17.0 New features:
Changes:
Corrections:
|
4.68.2 |
09/01/2019 |
PM compatibility: 1.16.1. Corrections:
|
4.68.1 |
12/11/2018 |
PM compatibility: 1.16.1. Corrections:
|
4.68.0 |
26/10/2018 |
PM compatibility: 1.16.1 New features:
|
4.67.0 |
12/06/2018 |
PM compatibility: 1.16.0 New features:
Changes:
Corrections:
|
4.66.1 |
09/05/2018 |
PM compatibility: 1.16.0 New features:
Changes:
Corrections:
|
4.65.1 |
19/02/2018 |
PM compatibility: 1.16.0 New features:
Changes:
Corrections:
|
4.60.0 |
20/11/2017 |
PM compatibility: 1.15.2 New features:
Changes:
Corrections:
|
4.59.3 |
15/11/2017 |
PM compatibility: 1.15.2 Corrections:
|
4.59.2 |
25/08/2017 |
Corrections:
|
4.59.1 |
26/06/2017 |
PM compatibility: 1.51.2 Corrections:
|
4.59.0 |
25/11/2016 |
PM compatibility: 1.15.1 Includes versions: 1.02.0 & 1.15.0. Option N compatibility: Minimum SW version 2.00.3 needed because limitation of 4000 text strings has been exceeded. New features:
Changes:
Corrections:
|
4.57.1 |
03/10/2016 |
PM compatibility: 1.15.0 Includes versions: 1.02.0 & 1.14.6. Option N compatibility: Minimum SW version 2.00.3 needed because limitation of 4000 text strings has been exceeded. Changes:
Corrections:
|
4.57.0 |
06/07/2016 |
PM compatibility: 1.15.0 Includes versions: 1.02.0 & 1.14.6. Option N compatibility: Minimum SW version 2.00.3 needed because limitation of 4000 text strings has been exceeded. New features:
Corrections:
|
4.56.0 |
01/06/2016 |
PM compatibility: 1.14.6 Includes versions: 1.02.0 & 1.14.5. Option N compatibility: Minimum SW version 2.00.3 needed because limitation of 4000 text strings has been exceeded. New features:
Changes:
Corrections:
|
4.55.0 |
17/07/2015 |
PM compatibility: 1.14.5 Includes versions: 1.02.0 & 1.14.4. New features:
Changes:
Corrections:
|
4.54.3 |
27/05/2015 |
Corrections:
|
4.54.2 |
01/04/2015 |
Corrections:
|
4.54.1 |
19/03/2015 |
New features:
Changes:
|
4.50.0 |
09/10/2014 |
New features:
Corrections:
|
4.40.3 |
11/06/2014 |
Corrections:
|
4.40.2 |
19/03/2014 |
Corrections:
Changes:
New features:
|
4.40.1 |
18/02/2014 |
PM compatibility: 1.14.1 Includes versions: 1.02.0 & 1.40.0. Option N compatibility: As a minimum, SW version 2.00.3 is needed due to exceeding of limitation of 4000 text strings. Corrections:
|
4.30.0 |
31/10/2013 |
Corrections:
New features:
|
4.30.1 |
31/10/2013 |
Corrections:
|
4.21.1 |
01/07/2013 |
Corrections:
Changes:
New features:
|
4.20.2 |
23/11/2012 |
PM compatibility: 1.12.1 Includes versions: 1.01.4 & 1.12.0. N-option compatibility: As a minimum, SW version 2.00.3 is needed due to exceeding of limitation of 4000 text strings. Corrections:
Changes:
|
4.20.1 |
02/11/2012 |
PM compatibility: 1.12.0 Includes versions: 1.01.4 & 1.11.2. Webarm/N-option compatibility: Mininum SW version 2.00.3 needed due to limitation of 4000 text strings exceeded. Corrections:
|
4.20.0 |
12/10/2012 |
PM compatibility: 1.12.0 Includes versions: 1.01.4 & 1.11.2. New features
Corrections:
|
4.10.2 |
12/07/2012 |
PM compatibility: 1.11.2 Includes versions: 1.01.3 & 1.11.1. Corrections:
|
4.10.1 |
11/07/2012 |
PM compatibility: 1.11.2 Includes versions: 1.01.3 & 1.11.1. Corrections:
|
4.10.0 |
10/07/2012 |
PM compatibility: 1.11.2 Includes versions: 1.01.3 & 1.11.1. New features
Changes:
Corrections:
|
4.04.0 |
04/03/2012 |
PM compatibility: 1.11.1 Includes versions: 1.00.0, 1.00.1, 1.00.2, 1.00.3, 1.10.0, 1.10.1, 1.10.2 & 1.11.0. New features:
Changes:
Corrections:
|
4.03.0 |
09/02/2012 |
PM compatibility: 1.11.0 Includes versions: 1.00.0, 1.00.1, 1.00.2, 1.00.3, 1.10.0, 1.10.1 & 1.10.2. New features:
Corrections:
|
4.02.0 |
01/02/2012 |
New features: Additional Delta Analogue alarms 4-6 added. Changes:
Corrections:
|
4.01.1 |
16/01/2012 |
|
4.01.0 |
16/12/2011 |
PM compatibility version 1.10.2. Includes versions: 1.00.0, 1.00.1, 1.00.2, 1.00.3, 1.10.0 & 1.10.1. New features:
Changes:
Corrections:
|
4.00.1 |
12/12/2011 |
PM compatibility version 1.01.1. Includes versions: 1.00.0, 1.00.1, 1.00.2 & 1.10.0. New features:
Corrections:
|
4.00.0 |
06/12/2011 |
PM compatibility version 1.10.0
|
On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).
Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.
DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.
DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.
Licence agreement for software downloaded from www.deif.com
Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.
The latest versions for full functionality
As always, we recommend that you install our offered improvements to fully utilise your DEIF product.
All improved software can be downloaded at your convenience at www.deif.com under “Software”.
Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.